Richard Sanders Military Series WMB

Prices are indicative only and are subject to change without notice due to quantity and frequency of production runs.

	Willys MB Parts
		MB engine pulley. $55.00 US Copy of original cast pulley but fully CNC turned in Steel Runs dead true.
		MB rev. idler gear. $86.00 US Made from tool steel case hardened, and precision machined.
		MB 1st rev. gear. $110.00 US Made from tool steel case hardened, and precision machined.
		MB roller chain and sprocket set. $225.00 US These are manufactured as a high precision timing chain set using modern automotive chain. Engine runs quieter and stay properly timed.(Very long lasting, lasts life of motor)
		MB Head stud set (15pcs) $151.00 US Fully precision machined from high tensile steel. We recommend using all head studs in your engine to reduce the risk of engine block damage caused by bolts.
		MB transfer case counter shaft. $53.00 US Made from high tensile tool steel deep case hardened for long life, and fitted with O rings to prevent oil leakage.
		MB counter shaft 3 speed. $42.00 US Suits cluster gear, made from tool steel and heavily case hardened for long life.
		MB counter shaft rev. idler. $35.00 US Suits cluster gear, made from tool steel and heavily case hardened for long life.
		MB bronze wheel cylinder pistons. $180.00 US Full set for one vehicle. Includes 4 x ¾ pistons and 4 x 1” pistons(With stainless steel shoe locators) For years we have all had the problem of the Aluminium wheel cylinder pistons corroding in the wheel cylinders and stopping the brakes working. No more is this a problem. Made of bronze these ones will not seize up when used with the cylinders sleeved in stainless steel, use silicon brake fluid and you are set for a long time. (My GPA has lasted 15 years using a set of these, and still going on the same set.)
		MB Wheel cylinders Sleeved in stainless steel $599.00 US (Set of 4pcs) The cylinders are sleeved in stainless steel and fitted our bronze pistons. This is a real long term fix that makes your wheel cylinders corrosion proof.
		MB water pump pulley. $60.00 US This is a full machined steel pulley that runs true. (Not pressed metal)
		M.V. grease fitting kit. $35.00ea US Grease nipple kit to suit MB/GPW/GP/GPA. Popular sizes for the whole vehicle.
		Air cleaner conversion kit. $ 95.00 US This kit converts your standard oil bath air cleaner to take a standard filter cartridge. Eliminating the need for oil changes, providing better protection for your motor and improving running. No modifications required. kit includes:- filter cartridge, adaptor ring and O-ring seal. Ready to fit.
		WMB Transfer case counter shaft rebuild kit. $195.00 US The counter shaft is made from high grade tool steel heat treated and ground finished to give a long life. To eliminate excessive end float in the Hyatt roller bearings we have manufactured a high grade gear bronze spacer that fits between the Hyatt assemblies. The thrust washers have been designed to compliment this assembly to further reduce end float and are made from solid gear bronze. The kit comes complete with high grade bearings that have been polished to reduce wear on the thrust washer faces.
		GPW Bell Crank Shaft + Washer. $65.00 US repair kit
		GPW Bell Crank Washer kit. $ 12.00 US
		Drive Shaft Replacement Spline. $65.00ea US Recondition your Drive Shaft by simply replacing the warn spline. We are proud to offer an exact replacement spline to suit your original front and rear drive shafts. (Slip Yoke not included)
	MB Parts ON the Drawing Board
	We can make other parts on request. Our main area of expertise is turned and cast parts. Our aim is not to compete with mass produced parts, but to make parts where people are not happy with the quality or normal producers are not prepared to make owing to the small volume. Note All Parts + Postage.

MB engine pulley. $55.00 US

MB roller chain and sprocket set. $225.00 US