Richard Sanders Military Serie0s FGPA

Prices are indicative only and are subject to change without notice due to quantity and frequency of production runs.

	Ford GPA Parts
		GPA Roller chain and sprocket set. $225.00 US Timing set for engine. Very long lasting, lasts life of motor.
		GPA Head stud set (15 pcs). $151.00 US Fully precision machined from high tensile steel. We recommend using all head studs in your engine to reduce the risk of engine block damage caused by bolts.
		GPA double row engine crank shaft pulley. $98.00 US Precision turned insolid steel, runs dead true.
		GPA winch drive shafts. $425.00 US This shaft is an exact copy or the original shaft that runs from the engine PTO drive to the Braden winch. It is fitted with correct universal joints same as the originals, machined to suit winch and PTO drive.
	No Picture Available	Rubber boots for GPA winch drive shaft. $52.00ea US These are rubber boot seals that slide over the universal joints on the winch Drive shaft. They are specifically designed to keep the grease on the universal joints and stop oil spray in the engine bay. (Two required per shaft)
		GPA replacement winch drive universal joint. $117.00 US Same style as original machined to suit winch or PTO. (Please state which on is required).
		GPA extended bell crank shafts. $85.00 US This is a precision machined bell crank shaft that is extended to raise the drag link to minimise risk of cutting the hull boot seal, made from high tensile steel, case hardened and ground.
		GPA belt kit. $65.00 US Consists of 3 belts to suit bilge pump, Winch PTO and fan drive. Belts are marked with GPA original style part number. (These are high quality reproduction belts). WE DO NOT RECOMMEND USE OF ORIGINAL BELTS AS BELTS DETERIORATE WITH AGE.
		GPA transfer case counter shaft. $53.00 US Made from high tensile tool steel deep case hardened for long life, and fitted with O rings to prevent oil leakage.
		GPA Counter shaft 3 speed. $42.00 US Suits cluster gear, made from tool steel and heavily case hardened for long life.
		GPA Counter shaft rev. idler. $35.00 US Suits cluster gear, made from tool steel and heavily case hardened for long life.
		GPA 1st rev. gear. $110.00 US Made from tool steel case hardened, and precision machined.
		GPA rev. idler gear. $86.00 US Made from tool steel case hardened, and precision machined.
		GPA bronze wheel cylinder pistons. $180.00 US Full set for one vehicle. Includes 4 x ¾ pistons and 4 x 1” pistons (With stainless steel shoe locators) For years we have all had the problem of the aluminium wheel cylinder pistons corroding in the wheel cylinders and stopping the brakes working. No more is this a problem. Made of bronze these ones will not seize up when used with the cylinders sleeved in stainless steel, use silicon brake fluid and you are set for a long time. (My GPA has lasted 15 years using a set of these, and still going on the same set.)
		GPA Wheel cylinders sleeved in stainless steel . $599.00 US (Set of 4pcs) The cylinders are sleeved in stainless steel and fitted with our bronze pistons. This is a real long term fix that makes your wheel cylinders corrosion proof.
		GPA Bilge pump nuts. $65.00ea US These nuts are exact copies of the originals cast in bronze.There are 5 required per vehicle and holds pipes to pump and 2 way valve.
		GPA Top radiator cross- over tube. $75.00 US Manufactured in stainless steel this pipe fits between the thermostat housing and the radiator. It has the correct bend in it to offset around the winch PTO drive. It is a quality reproduction of the original.
		GPA Bottom radiator pipe. $120.00 US Manufactured in stainless steel this pipe fits between the bottom radiator outlet pipe and the engine. It is a quality reproduction of the original.
		GPA Bilge pump impellor rubber. $121.00ea US This is a quality reproduction of the internal pump impellor enabling you to rebuild your original bilge pump. Made with bronze outer ring, and Polyurethane insert these are designed for many years reliable use. (Two required per pump).
		GPA Rear Tail light Brackets. $50.00ea US These are exact reproductions of the original tail light brackets that bolt to the battery covers. (2 required per vehicle).
		GPA Propeller shaft. $396.90 US This is the shaft that the water propeller attaches to. It is an exact copy of the original made from high tensile steel and precision machined.
		GPA water pump pulley. $60.00 US This is a full machined steel pulley machined with the longer hub to suit the GPA.
		GPA Clamp ring. $78.00 US Suits the rear drive tunnel and clamps the rubber seal to hull.
		GPA Pivot Ring. $98.00 US Suits the rear drive tunnel and is the pivot ring for the drive shaft tube.
		GPA shock absorber pins. $55.00ea US This pin holds the top of the shock absorber and screw through the hull into the chassis. Precision copies of the originals, and manufactured in high tensile steel. Comes with nuts washers and cotter pin. (4pcs required per vehicle).
		GPA windscreen rest Brackets. P.O.A. This is the top hat bracket that supports the windscreen when it is in the laid down position. Supplied with out webbing cushion. (2pcs required per vehicle)
		GPA radiator hatch linkages (set of 2pcs). $40.00 US These are the links that raise the radiator hatch. Exact copies of the originals.
		GPA rudder assemble. $450.00 US This is a precision copy of the original rudder complete with shaft. The vane is made of the correct material ground finished to the right thickness. The Vain has been riveted to the shaft to make it as authentic as possible. (Tiller arm not included).
		GPA tiller arm. $105.00 US Authentic copy of original.
		GPA Tiller Arm U brackets and Eye bolt set. $185.00 US These are the U brackets and eye bolts that the rudder cables attach to. Exact copies of the originals and comes with stepped bolt to attach to tiller arm and butter fly nuts for adjusting cables.
		GPA air duct control shaft (Fits across bow). $98.00 US This is the air duct control shaft that runs across the front of the bow. The air duct links attach to this, along with the main control rod.
		GPA Spring mount bracket. $60.00 US This is the very rear bracket that is riveted to the frame to hold the rear spring mount bracket. It is an exact copy made from the original drawings. (2 pcs required per vehicle).
		GPA Spring bush sets. $276.00 US GPA Fastener kit. $80.00 US Manufactured to look the same as the originals, but with high tensile stud, and graphite impregnated nylon bush. These spring bushes are designed to look the part but long out last the originals. Complete with fastener kit:- includes castle nuts, split pins, heavy gauge retaining washers and O rings. No modification required.
		GPA Exhaust pipe set stainless steel. $414.00 US Consists of 3 pipes with flexible section out of manifold copied from original pipes. Tail pipe is made longer than original so you can cut to required length to protrude or not through the side of the hull. (Please yourself) Made in 402 stainless steel.
		GPA Bilge pump pulley. $270.00 US This pulley is an exact copy of the original adjustable pulley that fits to the bilge pump. It is precision machined in solid steel for durable operation and yet still maintaining an authentic look.
		GPA Marine prop. Extractor tool. $225.00 US This tool is used to pull the marine prop from its shaft. Specially designed to easily fit around the prop and extract it from its shaft.
		GPA Suspension shackle links (set of 8pcs). $95.00 US These are the links that join the spring bush to the hanger bush. Complete with rounded edges like the originals. (A set of 8pcs are required per vehicle.)
		GPA Dash air duct door spring clips. $15.00ea US These are the small spring clips that fit to the inside of the dash board air duct door, and hold it tightly closed. These are exact copies of the originals made in spring steel. (3pcs required per vehicle)
	No Picture Available	GPA Bilge pump pipe set. $690.00ea US This is the complete set of 5 pipes made in stainless steel and comes complete with the brass nuts. The nuts and pipes are exact copies of the originals.
		GPA rudder cable kit. $80.00ea US This kit comes with the correct size stainless steel cable that runs from the steering box to the tiller arm. Included in the kit are two cable thimbles and clamp U bolts for attaching the cable to the tiller eye bolts.
	No Picture Available	GPA hull drain plugs. $35.00ea US These are fully machined in steel and cut with the correct tapered thread to suit the hull of the GPA. Five pieces are required for a set.
		M.V. grease fitting kit. $35.00ea US Grease nipple kit to suit MB/GPW/GP/GPA. Popular sizes for the whole vehicle.
		Air cleaner conversion kit. $ 95.00 US This kit converts your standard oil bath air cleaner to take a standard filter cartridge. Eliminating the need for oil changes, providing better protection for your motor and improving running. No modifications required. kit includes:- filter cartridge, adaptor ring and O-ring seal. Ready to fit.
		GPA Transfer case counter shaft rebuild kit. $195.00 US The counter shaft is made from high grade tool steel heat treated and ground finished to give a long life. To eliminate excessive end float in the Hyatt roller bearings we have manufactured a high grade gear bronze spacer that fits between the Hyatt assemblies. The thrust washers have been designed to compliment this assembly to further reduce end float and are made from solid gear bronze. The kit comes complete with high grade bearings that have been polished to reduce wear on the thrust washer faces.
		Drive Shaft Replacement Spline. $65.00ea US Recondition your Drive Shaft by simply replacing the warn spline. We are proud to offer an exact replacement spline to suit your original front and rear drive shafts. (Slip Yoke not included)
	GPA Parts ON the Drawing Board
	We can make other parts on request. Our main area of expertise is turned and cast parts. Our aim is not to compete with mass produced parts, but to make parts where people are not happy with the quality or normal producers are not prepared to make owing to the small volume Note All Parts + Postage.